---
title: Adding a Source – Failover
slug: zen-master/adding-a-source-failover
docTags:
createdAt: 2024-12-27T16:33:32.668Z
---
You can combine two or more Sources to create a unified* Failover* Source. Whenever one of the Sources is disrupted (or interrupted completely), ZEN Master will seamlessly merge the streams, retrieving the missing packets from the alternate Source.
The streams can be merged using one of the following methods:
- **Stream Switch - **ZEN Master treats the streams as different and does not try to merge them. If packets are missing from one stream, ZEN Master will switch to the alternate stream.
- **Content Hitless Merge **- if the Sources do not have RTP headers, Zixi will merge the streams using the MPEG-TS payload content itself. This method uses Zixi's patented DNA like sequencing algorithm to fill in the missing packets.
- **SMPTE 2022-7 Hitless **- if the Sources use RTP, and the RTP headers were maintained, Zixi can use the SMPTE 2022-7 to compare and merge the two streams. This option uses the sequence and the timestamp in the packets to compare which packets are missing, providing optimal results.
:::hint{type="info"}
* If the streams are not identical, the failover process will not be seamless and may take up to a second.
* You can manually select one of the streams to be active by clicking on the *Lock* button in the *Sources* tab of the *Source Details* page. The Source designated as Locked will be used whenever it is available until you click *Unlock*.
:::
Zero Bitrate and Offline events always trigger failover. For v15+ Broadcasters, you can configure additional rules to failover for other content quality errors (e.g. P1 Transport Events, Frozen Video etc.) that occur beyond a specified threshold.
The following procedure describes how to add a Failover Source in ZEN Master. In addition, an explanation of each of the configuration parameters is given in the table below.
### To add a Failover Source:
:::::WorkflowBlock
:::WorkflowBlockItem
In the main navigation, click **Sources**.
:::
:::WorkflowBlockItem
Click **+ Add**.
The **Create New Source selection** window is displayed.
:::
:::WorkflowBlockItem
Click on **Failover**.
The **Create New Failover** window opens.
:::
:::WorkflowBlockItem
In the **Info** section, in the **Name** field, enter a unique name to identify this Source in the system.
:::
:::WorkflowBlockItem
In the **Tags** field, select one or more of the predefined Tags from the drop-down list.
Tags are used for access control. By selecting a Tag, you are relating this Source to that Tag. Tags are associated with certain roles (through the Users & Roles screen), and roles, in turn, are associated with users and user groups. If you would like to create a new Tag, see [Creating a Tag](docId\:YpM9tw81ap6nq8sTKv4Rd).
:::
::::WorkflowBlockItem
In the **Events Configuration Profile** field, select from the dropdown list the profile that you would like to apply to this Source. By default, the *Default* profile is applied.
:::hint{type="info"}
*Events Profiles* consist of a series of rules that determine precisely how various types of Events are logged and what results they trigger.
:::
::::
:::WorkflowBlockItem
The Source's location is used to represent it in the proper position in the Map display (see [Maps](docId\:sFZM6JvoRvuigo7X0dNUE)). By default, the location is determined automatically based on the Source's IP. If you would like to manually set the location of the Source (Optional), use the following procedure:
1. Click on the **Edit** icon next to the **Location **field.
A search box is shown below the **Location** field.
2. Enter identifying info for the location (e.g. street address, zip code, coordinates).
Search results are displayed below the search box as you type.
3. Click on the desired location.
The selected location populates the **Location** field.
:::
::::WorkflowBlockItem
In the **Input** section, in the **Sources **field, select two or more Sources that you would like to include in the failover group.
:::hint{type="info"}
If the selected Sources are not binary identical then there will be a one second delay in the failover to the backup source.
:::
As you select sources, they will appear in the table below the selector:
::::
::::WorkflowBlockItem
For each source, configure the following:
- Under **Priority** - to designate a Source as a preferred Source, select the **Preferred** checkbox or to to designate a Source as a Slate, select the **Slate** checkbox. Preferred source take precedence over non-preferred source (i.e., sources that were not marked as preferred). Slate sources are sources that stream slate content, which is content that can be served when there are gaps in a live stream ad break that cannot be filled with a dynamically-served ad.
- Under **Min Bitrate (Kbps) - **specify the bitrate threshold level in Kbps to perform the failover (i.e., if the bitrate drops under the threshold the failover will take place).
:::hint{type="info"}
If you would like to remove a selected Source, click on the **-** button next to the Source.
:::
::::
:::WorkflowBlockItem
In the **Max Bitrate** selector, leave the selection at Auto to let ZEN Master calculate the max bitrate for the failover source using the bitrates of the component sources. Or you can choose a max bitrate from the available options if you prefer.
:::
:::WorkflowBlockItem
For **Failover Mode**, select the desired mode for failing over/merging the streams. Options are:
- **Stream Switch** – ZEN Master treats the streams as different and does not try to merge them. If packets are missing from one stream, ZEN Master will switch to the alternate stream. If the payload is not binary identical it will fall back to Stream Switch.
- **Content Hitless** - if the Sources do not have RTP headers, Zixi will merge the streams using the MPEG-TS payload content itself. This method uses Zixi's patented DNA like sequencing algorithm to fill in the missing packets.
- **SMPTE 2022-7 Hitless **- if the Sources use RTP, and the RTP headers were maintained, Zixi can use the SMPTE 2022-7 to compare and merge the two streams. This option uses the sequence and the timestamp in the packets to compare which packets are missing, providing optimal results.
:::
::::WorkflowBlockItem
If you have selected the **Content Hitless** or the **SMPTE-2022-7 Hitless** option, in the **Merge Search Window \[ms] **field, enter the time frame for which the system will search for the relevant packets in a matching stream. (Default: 1000)
:::hint{type="info"}
- If there is a latency difference between the streams, the *Search Window* value should be higher than the latency difference between the streams.
- If *Merge Mode* is Disabled, the time period specified in the *Search Window* field defines how long the stream will wait for packet before attempting to switch between streams.
:::
::::
:::WorkflowBlockItem
If you have selected the **Stream Switch** option, in the **Zero Bitrate/Offline Detection Window \[ms]** field, enter the time frame with zero bitrate or offline state after which the system will perform the failover
:::
::::WorkflowBlockItem
**Failover Rules **allow you to set rules for what type of error and how often they occur to change to the failover stream. If you would like to change the rules, use the following procedure (supported for Broadcasters v15+):
1. Select the Checkbox next to the error for which you would like to change the error rules. Options are: *P1 Transport Errors, Frozen Video, Blank Picture,* *Silent Audio, and Low Bitrate*. (*Zero Bitrate/Offline* is set as selected on a fixed basis.)
2. Set the parameters for:
- **Sample Duration** - the duration (in seconds) of the window of each sample.
- **Samples** - the number of samples that you check in each sampling.
- **Samples Threshold** - the number of error results (within a sampling) that trigger the failover.
- **PID** - scopes the rule to a specific PID in the transport stream (e.g., if you have multiple audio programs it will only apply the rule to the specified one)
:::hint{type="info"}
For example, if you set Sample Duration=10, Samples=6, Samples Threshold=2: then if during a 60 second time period an error occurs during 2 out of the 6 ten-second windows, failover will be triggered.
:::
::::
:::WorkflowBlockItem
In the **Configuration** section, in the **Ingest Cluster** field, select from the drop-down list the Ingest Cluster on which the Sources that you would like to group together are located.
:::
:::WorkflowBlockItem
In the **Target Broadcaster/s** field, specify which Broadcaster/s within the cluster on which ZEN Master can deploy the source. Either select a specific broadcaster (for Manual clusters) OR specify your preference for using primary vs. backup broadcasters, options are: *Prefer primary Broadcasters, Primary Broadcasters only, Backup Broadcasters only* or *Prefer Backup Broadcasters*.
:::
:::WorkflowBlockItem
Select the **Alert on PID changes** checkbox if you would like to generate email notifications whenever a PID change is detected.
:::
::::WorkflowBlockItem
Select the **Log SCTE-35** checkbox if you would like to log SCTE-35 markers for this stream.
:::hint{type="info"}
- To log SCTE-35 markers, SCTE-35 needs to be enabled both on the Ingest Cluster and on the Source configuration.
- SCTE-35 logging is only available for v13.1.40262+ Broadcasters.
:::
::::
:::WorkflowBlockItem
If **Log SCTE-35** was selected, you can choose to receive alerts for SCTE-35 markers by selecting the **Enable SCTE-35 alerts** checkbox.
:::
:::WorkflowBlockItem
Additional SCTE-35 options are available when you expand the **SCTE-35 Manipulation** section:
Here you can:
- Enable SCTE-35 Manipulation
- Specify the length of a search window for a NULL packet for SCTE-35 intertion
- Set the SCTE-35 PID
- Remove any existing SCTE-35 messages from the stream
See the **Parameters Table** below for an explanation of these options.
:::
:::WorkflowBlockItem
In the **Public Output** field, if you would like to allow access to the stream directly through a supported player, select the **Allow** checkbox.
:::
:::WorkflowBlockItem
If you selected the **Allow** checkbox, then enter a password in the **Password **field to authenticate access to the stream.
:::
::::WorkflowBlockItem
Under **Content Analysis** select one of the following options:
- **Full **- select this option if you would like to enable full Content Analysis (CQA), including analysis of the stream's audio and video content, including audio levels, audio silence detection, frozen video detection, and more.
- **TR101 Only** - select this option to perform TR101 analysis only (without video and audio content analysis). The analysis can be used to check the integrity of the TS and the most important elements of the stream. The analysis includes priority 1 and 2. To learn more about TR101 analysis see [TR 101 290 Technical Report](https://www.etsi.org/deliver/etsi_tr/101200_101299/101290/01.03.01_60/tr_101290v010301p.pdf).
- **None **- no content analysis is enabled.
:::hint{type="info"}
It is generally recommended to enable full Content Analysis unless it is causing technical problems. If Content Analysis is disabled, the system won't detect errors in the video and audio content of the stream and won't generate warnings for such events.
:::
::::
::::WorkflowBlockItem
If you would like to monitor CEA-608 closed captions, select **Monitor CEA-608 **checkbox**.**
:::hint{type="info"}
Monitoring CEA-608 Closed Captions requires using a version 14.4 or newer Broadcaster.
:::
If you would like to monitor CEA-708 closed captions, select **Monitor CEA-708 **checkbox**.**
:::hint{type="info"}
Monitoring CEA-708 Closed Captions requires using a version 14.4 or newer Broadcaster.
:::
::::
::::WorkflowBlockItem
If you would like to disable auto-pull, select the **Disable Auto-Pull** checkbox.
:::hint{type="info"}
Disabling Auto-Pull will lock Channels using this Source to the Source's Ingest Cluster and Targets to the Source's current active Broadcaster. This setting only applies to Pass-Through Channels.
:::
::::
:::WorkflowBlockItem
If Auto-Pull is *enabled*, in the **Auto-Pull Latency \[ms]** field, specify the maximum latency for auto-pull actions. The Broadcaster will update the latency as required, by using the maximal defined latency and then reducing the latency gradually. (Default: 1000 ms)
:::
::::WorkflowBlockItem
In the **WebRTC Playback** section, select the desired playback method.
:::hint{type="info"}
WebRTC enables you to monitor the stream via web browsers and mobile applications with real-time communication (RTC). WebRTC needs to be activated independently for each Source in ZEN Master (by default it is disabled).
:::
Select one of the following options:
- **Disabled **- users will not be able to view this Source using WebRTC (default)
- **Pass-Through** - passes the stream through to WebRTC without transcoding. This option *can only be used *if the input stream is already in a WebRTC compliant format (video - H.264 codec with *Baseline *or *Main *profile and no B frames, Audio - Opus codec).
- **Auto **- ZEN Master automatically transcodes the stream using the optimal profile for each specific user. In this option Zixi Broadcaster will decode the video, transforming it into RAW frames, which will be passed to the WebRTC library, where it will be re-encoded for each individual user.
:::hint{type="info"}
Best quality. However, if monitored by multiple users this can consume extensive resources.
:::
- **1080p/720p/480p/360p** - ZEN Master transcodes the stream to a WebRTC compliant profile with the specified resolution. The transcoding is done by Zixi Broadcaster's transcoder.
:::hint{type="info"}
This method requires a Zixi Broadcaster with X264 or Nvidia for transcoding. This method allows many users to monitor the stream without encoding separately for each individual user, which saves CPU capacity. Since there is only one stream version, it is recommended to encode to a low resolution and low bitrate so that the stream will be viewable by all users monitoring the stream.
:::
::::
:::WorkflowBlockItem
In the **Initial State** section, select the **Disabled** checkbox if you would like to disable this Source upon initial configuration.
:::
::::WorkflowBlockItem
Select the **Muted** checkbox if you would like to disable error/recovery notifications for this Source upon initial configuration.
:::hint{type="info"}
You can Enable/Unmute the Source at any time.
:::
::::
::::WorkflowBlockItem
Under **Error Concealment,** click the Enable Error Concealment checkbox to enable the following error concealment mechanisms that can correct transaport stream for downstream IRDs:
:::Paragraph{indent="1"}
1\. **Continuous Timeline** - corrects errors that are related to timeline jumps in the source. This mechanism will normalize the timeline by creating a variant of the input (the input is doubled) and normalizing the timeline of the doubled input.
:::
:::Paragraph{indent="1"}
2\. **Replace Frames** - If there are frames with CC errors, it replaces them with skip frames (inserts the last good frame received in place of missing ones). This solves issues such as an IRD that lost synchronization when it received broken frames. This mechanism also creates a variant of the input (doubling the input).
:::
:::Paragraph{indent="1"}
3\. **Renumber CC **- The Continuity Counter is part of the TS encapsulation. When there are CC errors in TR101 analysis it means that the counter has a gap due to the lost frames. This mechanism can re-write the CC counter for the downstream devices, so they will see a continuous increase of the counter.
:::
:::Paragraph{indent="1"}
4\. **Delay (ms) **- Enter the delay that the Error Concealment adds to the stream in miliseconds. Error Concealment needs to buffer the stream to analyze it. One second is a reasonable value. Lower values may cause the Error Concealment to not be able to fix some of the frames.
:::
:::Paragraph{indent="1"}
5\. **CBR Padding** - enter a value for the rate at which padding will be added to maintain a specific output transport bitrate. For example, if you have a video bitrate at 5000 kbps or that varies from 3000-5000 kbps and audio at 64 kbps, total bitrate will be max 5064 kbps or min 3064 kbps. With CBR padding set at 6000 kbps, 6000 kbps is being delivered downstream at all times, ensuring a consistent bitrate.
:::
:::Paragraph{indent="1"}
6.** PCR Interval** - Select the frequency at which Program Clock Reference is inserted into the outputs Transport stream. This depends on standard used by downstream encoders or decoders. Options include:
:::
:::Paragraph{listStyleType="disc" indent="2"}
ATSC standard - 100 ms
:::
:::Paragraph{listStyleType="disc" indent="2"}
DVB standard - 40 ms
:::
7. **Remux Buffer Size** - Specify the time added for remuxing the stream (default: 2500 ms).
8. **Smoothing** - Time added for smoothing a bursty stream - adds to latency, but produces a smoother output.
See [Improving Stream Resiliency: Error Correction and Concealment](docId:9_OLo1Argk_2aDoSHYFBb) for more information.
::::
:::WorkflowBlockItem
If you would like to adjust the advanced settings, click **Advanced**.
The Advanced settings fields are displayed:
:::
:::WorkflowBlockItem
If you would like to track usage for this Source, enter your **Billing Code** details. See [Billing Codes](docId\:lalXJ_N928TeGCPDpBirJ) .
:::
:::WorkflowBlockItem
In the **Auto Pull MTU** field, specify the maximum transmission unit (largest data packet that a network-connected device will accept) in bytes for the Auto Pull.
:::
:::WorkflowBlockItem
To set the detection of frozen video, in the** Frozen Video Minimal Duration **field, specify the default minimal duration in seconds of frozen video after which the Broadcaster will trigger a Frozen video alert. Default: 10 seconds. This setting is supported for Broadcaster version 16.3 and higher.
:::
:::WorkflowBlockItem
To set the detection of blank video, in the **Blank Video Minimal Duration** field, specify the default minimal duration in seconds of blank video after which the Broadcaster will trigger a Blank video alert. Default: 10 seconds. This setting is supported for Broadcaster version 16.3 and higher.
:::
:::WorkflowBlockItem
Click **Save**.
:::
:::::
### Hitless Failover Source Configuration Parameters Table
| **Parameter** | **Description** |
| ---------------------------------------------------------------------- | ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ |
| ***Info*** | |
| Name | Specify a name for the Failover Source in ZEN Master. |
| Tags | Select one or more of the predefined Tags from the drop-down list.
Tags are used for access control. By selecting an Tag, you are relating this Source to that Tag. Tags are associated with certain roles (through the Users & Roles screen), and roles, in turn, are associated with users and user groups. If you would like to create a new Tag, see [Creating a Tag](docId\:YpM9tw81ap6nq8sTKv4Rd) . |
| Events Configuration Profile | Select from the dropdown list the profile that you would like to apply to this Source. By default, the *Default* profile is applied.
Note: *Events Profiles *consist of a series of rules that determine precisely how various types of Events are logged and what results they trigger. |
| Location (Optional) | The Source's location is used to represent it in the proper position in the Map display (see [Maps](docId\:sFZM6JvoRvuigo7X0dNUE) ). By default, the location is determined automatically based on the Source's IP. Enter identifying info for the location (e.g. street address, zip code, coordinates) and select the desired location from the suggestions that are shown. |
| ***Input*** | |
| Sources | Select from the drop-down list two or more binary identical Sources that you would like to include in the failover group.
If the selected Sources are not binary identical then there will be a one second delay in the failover to the backup Source.
If you would like to designate a Source as a preferred Source, select the **Preferred** checkbox.
If you would like to designate a Source as part of the Slate, select the **Slate** checkbox.
In the **Min. Bitrate\[kbps]** field, specify the bitrate threshold level in Kbps to perform the failover (i.e., if the bitrate drops under the threshold the failover will take place).
**Note: **If you would like to remove a selected Source, click on the button next to the Source. |
| Failover Mode | Select the desired mode for failing over/merging the streams. Options are:
* **Stream Switch – **ZEN Master treats the streams as different and does not try to merge them. If packets are missing from one stream, ZEN Master will switch to the alternate stream. If the payload is not binary identical it will fall back to Stream Switch.
* **Content Hitless** - if the Sources do not have RTP headers, Zixi will merge the streams using the MPEG-TS payload content itself. This method uses Zixi's patented DNA like sequencing algorithm to fill in the missing packets.
* **SMPTE 2022-7 Hitless **- if the Sources use RTP, and the RTP headers were maintained, Zixi can use the SMPTE 2022-7 to compare and merge the two streams. This option uses the sequence and the timestamp in the packets to compare which packets are missing, providing optimal results. |
| Merge Search Window \[ms] | Specify the time frame for which the system will search for the relevant packets in a matching stream. (Default: 1000)
Note: If there is a latency difference between the streams, the Search Window value should be higher than the latency difference between the streams. |
| Zero Bitrate/Offline Detection Window \[ms] (for Stream Switch option) | Enter the time frame with zero bitrate or offline state after which the system will perform the failover. |
| Failover Rules | **Failover Rules** allow you to set rules for what type of error and how often they occur to change to the failover stream. If you would like to change the rules, use the following procedure (supported for Broadcasters v15+):
1) Select the checkbox next to the error for which you would like to change the error rules. Options are: *P1 Transport Errors*, *Frozen Video*, *Blank Picture,* *Silent Audio, and Low Bitrate*.
2) Set the parameters for:
- **Sample Duration** – the duration (in seconds) of the window of each sample.
- **Samples** – the number of samples that you check in each sampling.
- **Samples Threshold **– the number of error results (within a sampling) that trigger the failover.
- **PID** - scopes the rule to a specific PID in the transport stream (e.g., if you have multiple audio programs it will only apply the rule to the specified one)
Note: For example, if you set Sample Duration=10, Samples=6, Samples Threshold=2: then if during a 60 second time period an error occurs during 2 out of the 6 ten-second windows, failover will be triggered. |
| ***Configuration*** | |
| Ingest Cluster | Select from the drop-down list one of the available Ingest Clusters as the destination for the Source. |
| Target Broadcaster/s | Specify which Broadcaster/s within the cluster on which ZEN Master can deploy the source. Either select a specific Broadcaster to be used OR specify your preference for using primary vs. backup Broadcasters. Options are: *Prefer primary Broadcasters, Primary Broadcasters only*,* Backup Broadcasters only *or* Prefer Backup Broadcasters.*
Note: For managed clusters, it is not recommended to select a specific Broadcaster, as the Broadcaster’s availability may not remain stable. |
| Alert on PID changes | If you would like to generate email notifications whenever a PID change is detected, select this checkbox. |
| Preserve RTP Headers | Select this checkbox to preserve the RTP headers (which include the timestamps and sequences) and propagate them the output. |
| Log SCTE-35 | If you would like to log SCTE-35 markers for this stream, select this checkbox.
Note**:** To log SCTE-35 markers, SCTE-35 needs to be enabled both on the Ingest Cluster and in the Source configuration.
Note**:** SCTE-35 logging is only available for v13.1.40262+ Broadcasters. |
| Enable SCTE-35 alerts (for Log SCTE-35) | If you would like to receive alerts for SCTE-35 markers, select this checkbox |
| Public Output | If you would like to allow access to the stream directly through a supported player, select the **Allow** checkbox. |
| Password (for Public Output) | If you selected **Allow** in the *Public Output* field, specify a password in this field to authenticate access to the stream. |
| Content Analysis | Select one of the following options:
* **Full **- select this option if you would like to enable full Content Analysis (CQA), including analysis of the stream's audio and video content, including audio levels, audio silence detection, frozen video detection, and more.
* **TR101 Only** - select this option to perform TR101 analysis only (without video and audio content analysis). The analysis can be used to check the integrity of the TS and the most important elements of the stream. The analysis includes priority 1 and 2. To learn more about TR101 analysis see TR 101 290 Technical Report.
* **None** - no content analysis is enabled.
**Note**: It is generally recommended to enable full Content Analysis unless it is causing technical problems. If Content Analysis is disabled, the system won't detect errors in the video and audio content of the stream and won't generate warnings for such events. |
| Monitor CEA-608/CEA-708 Closed Captions | If you would like to monitor CEA-608/CEA-708 closed captions, select this checkbox.
Note: Monitoring CEA-608/CEA-708 Closed Captions requires using a version 14.4 or newer Broadcaster. |
| Disable Auto-Pull | If you would like to disable auto-pull, select this checkbox.
Note: Disabling Auto-Pull will lock Channels using this Source to the Source's Ingest Cluster and Targets to the Source's current active Broadcaster. This setting only applies to Pass-Through Channels. |
| Auto-Pull Latency \[ms] | Specify the desired latency for auto-pull actions. (Default: 1,000 ms) |
| WebRTC Playback | Select the desired playback method.
Note: WebRTC enables you to monitor the stream via web browsers and mobile applications with real-time communication (RTC). WebRTC needs to be activated independently for each Source in ZEN Master (by default it is disabled).
Select one of the following options:
* **Disabled** - users will not be able to view this Source using WebRTC (default).
* **Pass-Through** - passes the stream through to WebRTC without transcoding. This option *can only be used *if the input stream is already in a WebRTC compliant format (video - H.264 codec with *Baseline* or *Main *profile and no B frames, Audio - Opus codec).
* **Auto **- ZEN Master automatically transcodes the stream using the optimal profile for each specific user. In this option Zixi Broadcaster will decode the video, transforming it into RAW frames, which will be passed to the WebRTC library, where it will be re-encoded for each individual user.
Note: Best quality. However, if monitored by multiple users this can consume extensive resources.
* **1080p/720p/480p/360p** - ZEN Master transcodes the stream to a WebRTC compliant profile with the specified resolution. The transcoding is done by Zixi Broadcaster's transcoder.
Note: This method requires a Zixi Broadcaster with X264 or Nvidia for transcoding. This method allows many users to monitor the stream without encoding separately for each individual user, which saves CPU capacity. Since there is only one stream resolution, it is recommended to encode to a low resolution and low bitrate so that the stream will be viewable by all users monitoring the stream. |
| ***SCTE-35 Manipulation *** | |
| Enable SCTE-35 Manipulation | Select checkbox to enable SCTE-35 Manipulation. |
| SCTE-35 PID | Set the SCTE-35 PID in which the messages will be inserted. |
| Remove Existing SCTE-35 | Remove any existing SCTE-35 messages from the stream. |
| NULL Packet Search Window (ms) | Look for a NULL packet to insert SCTE-35 messages into the stream
* If the stream is **VBR**, set the value to `0` - SCTE-35 messages can be inserted anywhere, and do not need a NULL packet
* If the stream is **CBR**, the downstream receiver *may* need a CBR stream. Inserting the SCTE-35 message into a NULL packet ensures the stream will remain CBR; however, it may delay the insertion of the message up to the length of the search window |
| *Initial State* | |
| Disabled | Select this checkbox if you would like to disable this Source upon initial configuration. |
| Muted | Select this checkbox if you would like to disable error/recovery notifications for this Source upon initial configuration. |
| ***Error Concealment*** | |
| Enable Error Concealment | Select this checkbox to enable the error concealment mechanisms listed below to correct transport stream for downstream IRDs. |
| Continuous Timeline | Corrects errors that are related to timeline jumps in the source. This mechanism will normalize the timeline by creating a variant of the input (the input is doubled) and normalizing the timeline of the doubled input. |
| Replace Frames | If there are frames with CC errors, it replaces them with skip frames (inserts the last good frame received in place of missing ones). This solves issues such as an IRD that lost synchronization when it received broken frames. This mechanism also creates a variant of the input (doubling the input). |
| Renumber CC | encapsulation. When there are CC errors in TR101 analysis it means that the counter has a gap due to the lost frames. This mechanism can re-write the CC counter for the downstream devices, so they will see a continuous increase of the counter. |
| Delay (ms) | Enter the delay that the Error Concealment adds to the stream in miliseconds. Error Concealment needs to buffer the stream to analyze it. One second is a reasonable value. Lower values may cause the Error Concealment to not be able to fix some of the frames. |
| CBR Padding (kbps) | Enter a value for the rate at which padding will be added to maintain a specific output transport bitrate. For example, if you have a video bitrate at 5000 kbps or that varies from 3000-5000 kbps and audio at 64 kbps, total bitrate will be max 5064 kbps or min 3064 kbps. With CBR padding set at 6000 kbps, 6000 kbps is being delivered downstream at all times, ensuring a consistent bitrate. |
| PCR Interval (ms) | Select the frequency at which Program Clock Reference is inserted into the outputs Transport stream. Options include:
* ATSC standard - 100 ms
* DVB standard - 40 ms |
| ***Advanced*** | |
| Billing Codes | If you would like to track usage for this Source, enter you **Billing Code** details, see . (Supported for Broadcasters v14.8+) |
| Billing Channel ID | An optional arbitrary string - you can enter anything you want to for your record-keeping. This is **not** related to ZEN Master Channels. |
| Billing Password | Enter the password that corresponds to this billing code. |
| Auto- Pull Billing Code | Specify the maximum transmission unit (largest data packet that a network-connected device will accept) in bytes for the Auto Pull. |
| Auto- Pull Billing Password | Enter the password that corresponds to this auto-pull billing code. |
| Auto Pull MTU (bytes) | Specify the maximum transmission unit (largest data packet that a network-connected device will accept) in bytes for the Auto Pull. |
| Frozen Video Minimal Duration (seconds) | Specify the default minimal duration in seconds of frozen video after which the Broadcaster will trigger a Frozen video alert. Default: 10 seconds. This setting is supported for Broadcaster version 16.3 and higher. For existing sources, you may need to restart the source. |
| Blank Video Minimal Duration (sec) | Specify the default minimal duration in seconds of blank video after which the Broadcaster will trigger a Blank video alert. Default: 10 seconds. This setting is supported for Broadcaster version 16.3 and higher. For existing sources, you may need to restart the source. |
| Ignore Monitoring PIDs | Ignore PIDs for empty audio streams to prevent false warnings - enter a comma-delimited list of PID numbers that should not be monitored for null content. |