---
title: Single PUSH Transmission to Redundant Targets (Warm Redundancy)
slug: product-features/single-push-transmission-to-redundant-targets-warm-redundancy
docTags: 
createdAt: 2024-12-08T16:24:07.574Z
---



![](https://api.archbee.com/api/optimize/mzxtTQEvCNIdUNgF2kuwJ/s_4zUBtcbMv3F2jkZY-KV_zec-image.png)

A Zixi PUSH output can be configured with multiple, ordered, fail-over targets. The topology includes a source node (in this case a ZEC) pushing a stream to a primary target (in this example the Primary Broadcaster). In the event that the primary target is not available, due to connection loss or hardware/software failure, the source node automatically switches to the secondary target. Additional targets can be configured with the same fail-over mechanism. The source node will attempt to connect to the primary again only in the event that the secondary connection is lost. 

## Source Configuration

The following procedure describes how to configure the ZEC to push a single stream to a primary host and an option to push the same stream to alternative hosts in the event that the primary host is unavailable. The procedure does not cover instructions on how to configure the Input into the ZEC. 

**To configure the source node (e.g. ZEC):**

1. On the **Outputs** page of ZEC, click the **New Output** button, located in the upper- right end corner of the screen.
2. In the **Name** field, type a new name for the output. 
3. Select the **Push **radio button.
4. In the **Input Stream** field, select the relevant input stream.
5. In the **Output Name **field, enter a stream ID (alphanumeric) . The same Stream ID will be also configured in the target nodes (Push Inputs).
6. Optional - in the **Password** field, specify a string to be used at the destination to authenticate that the pushing Broadcaster is allowed to push this stream.
7. In the **Max Latency** field, specify the buffer size that Zixi Broadcaster will keep for error correction. For example, 6000 milliseconds would ensure that the stream is protected for six seconds of errors in the network. Default: 6000.
8. In the **Host** field, enter the host name or IP of the primary target.
9. In the **Port** field, specify the destination port to listen on for the Push stream (default: 2088).
10. In the **Local IP** field, select from the drop-down menu, the IP address of the NIC (Network Interface Card) in the Source through which the stream will be pushed.
11. Click the **"+"** button to add another (secondary) target.
    Another line is added with the properties of the secondary destination. 
12. Fill out the secondary destination parameters.
13. To add additional destination(s), click the "+" and fill out the destination parameters.
14. Click **OK**.

![](https://api.archbee.com/api/optimize/mzxtTQEvCNIdUNgF2kuwJ/8IOUNmpoLAq59ghGGGsDi_image.png)

## Target Configuration

The following procedures describe how to configure the two or more target Zixi Broadcasters in a warm redundancy configuration. These targets must use the same Stream ID that was used to configure the Source in the ZEC. 

**To configure the primary target node (e.g. Zixi Broadcaster):**

1. Click the **Inputs **tab at the top of the primary Zixi Broadcaster administrative screen
2. Click **New Input **on the upper right hand side of the screen.
3. In the **Stream ID** field, enter the same “Stream ID” as the source output.
4. Select the **Push **radio button option.
5. In the **Password** field, if you have configured a password in the source (ZEC output), enter the same password.
6. Configure additional parameters as required. 
7. Click **OK**.

![](https://api.archbee.com/api/optimize/mzxtTQEvCNIdUNgF2kuwJ/WeXTIho7XHOwbKJOezizu_image.png)

**To configure the secondary target node(s) (e.g. Zixi Broadcaster):**

1. Click the **Inputs **tab at the top of the secondary Zixi Broadcaster administrative screen
2. Click **New Input **on the upper right hand side of the screen.
3. In the **Stream ID** field, enter the same “Stream ID” as the source output. This is the same Stream ID that was also entered in the primary target. 
4. Select the **Push **option.
5. Configure additional parameters as required. 
6. Click **OK**.
7. Repeat the steps above to configure additional target nodes as necessary. Each target node needs to be configures in the Zixi Feeder (source) output. 

## Cost Considerations

This topology duplicates the target side Zixi node software and hardware components. However, it does not require doubling the up-link bandwidth, as the backup connection stream will be only active in the event that the primary stream fails.

## Latency Considerations

For detailed recovery time details, please contact your Zixi representative.